The Asia Miner

SEP-OCT 2014

The ASIA Miner - Reporting Important Issues to Mining Companies in the Asia Pacific Region

Issue link: https://asiaminer.epubxp.com/i/381094

Contents of this Issue

Navigation

Page 69 of 91

68 | ASIA Miner | September/October 2014 REAL-TIME analysis technologies for con- veyed bulk materials have been used in the coal industry since the early 1980s. In the last 10 years Scantech, an Australian company specializing in on-conveyor analysers, has in- troduced this analysis to the minerals industry. The key to process control using on-belt analysis is that results are available every two to fve minutes, permitting real-time process control. Dual Energy Transmission (DUET) is the most commonly used on-belt ash measure- ment technique for coal and Scantech's Coalscan 2100 makes use of this. New de- velopments in DUET technology permit coal depths up to 400mm to be measured. Scantech's on-conveyor coal elemental analysers, known as Coalscan 9500X, anal- yse the entire stream, avoiding not only the operating and capital costs of sampling, but also the sensitivity of older technologies to variation in ash mineralogy. This technology is no longer sensitive to variations in bed depth or layering of different coal types. As well as measuring ash, this technology mea- sures ash oxides, total sulphur and many other parameters useful for effcient plant control. In minerals industries the technology is used in the Geoscan analyser with success- ful installations used to measure grades of iron ore, phosphate, copper, manganese and lead-zinc. There have been four Geo- scan generations with the latest requiring minimal maintenance, having very low lev- els of external radiation and providing drift-free analysis. A South East Asian copper-gold operation identifed the need for plant feed analysis in real-time to improve control of copper metal units entering its processing plant due to a lim- ited leach circuit capacity for dissolved copper metal. The mining operations recovered ore from several open pits where grade varied be- tween less than 1% and greater than 8%. Mine planning information was used to determine the expected average copper grade for each blast, which was then hauled to the designat- ed ROM stockpile and blended with ore from other stockpiles into a crusher and conveyed to a mill. The plant was unable to utilize a slurry analyser on the milled ore as acidic solution added to the mill resulted in copper being tak- en into solution. Slurry analysis would not have been suitable to measure the copper in solu- tion thereby ruling out this option. Commissioning a Scantech Geoscan and moisture monitor. On-belt analysis for minerals industry A Geoscan analyser was commissioned in early 2008 on the crushed ore conveyor. The copper content in the feed is controlled by adjusting the blend from the ROM stockpiles about every 30 minutes as needed. Stockpiles often contain zones of low and high grade material resulting in large varia- tions in average feed grade which can result in times where copper metal content exceeds the leach plant capacity. When this occurs excess copper is not recovered, while at oth- er times a lower than expected copper metal throughput results in the leach circuit being un- der-utilized. The economics of these extremes and likelihood of their occurrence resulted in the need for improved process control of plant feed quality. It was estimated by metallurgical staff that the analyser payback would be in the order of eight weeks if these situations could be prevented. Through experience with the analyser the site also found benefts in knowing the sulphur and iron content of the ore as pyrite was a requirement for leach process performance. Pyritic ore was able to be added when iron and sulphur levels were below the desired tar- get range. The Geoscan proved reliable and effective and continues to be an integral part of plant operation. These technologies can be combined with the microwave moisture monitor, so that a complete analysis of the material is available in real time. Scantech produces standalone moisture monitors. The TBM 210 was devel- oped about 20 years ago and is installed at many sites and in different applications moni- toring moisture levels in shipments, optimizing washery performance and maintaining appro- priate levels for dust suppression. Moisture monitors are widely used in iron ore installa- tions in South Africa and Australia. The TBM 230 has recently been introduced for denser materials and deeper bed depths up to about 600mm. On-belt analysis allows more effcient use of the resource, more effective process control and more cost effective methods of mining, processing, utilizing and disposal. On-belt analysis should be viewed not simply as an alternative to laboratory analysis. Scantech, working with local agents, has found that the most benefcial on-belt analyser installations are generally those where the user realizes the advantages real-time analysis can bring.

Articles in this issue

Archives of this issue

view archives of The Asia Miner - SEP-OCT 2014